search

Marathon Sprint Series Betriebsanleitung Seite 17

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 35
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
    •
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 16
Installation duo
16
• Position, align and the secure control housing using 4 screws (1).
Supplied components 2 plugs, 2 screws.
• Slot the control board (1) into terminal bar (2) and slide it into the
housing.
Touch the control unit (3) only at its edge!
Do not touch the electronic components!
• Install the control unit (3). Mount the lamp hood (2) and tighten the
screws (1).
Installing the socket Outlet
Socket outlet may only be installed by a qualified electrician.
Protect socket with a fuse (16 A slow-blow).
Observe all applicable regulations (e.g. VDE, etc.)!
• Install socket (1) on ceiling at a distance of approx. 0.5 meters to the
control unit housing (2).
• Install and connect the connection cable from the socket outlet (1) to
the mains power supply. Do not plug the connector into the socket
outlet yet!
30
H
30 C30
1
3
2
29
29
2
1
3
28
27
28
2
1
2
3
4
5
6
3 4
1
2
3
4
5
6
5
5
7
7
8
8
4
4
6
6
3
3
2
2
1
1
O
N
ON
D
IP
DIP
2
2
3
3
4
4
5
5
6
6
1
1
1
27
3
4x
Installing and connecting and
additional push-button
Only necessary if a further push-button is required in addition to
the one already installed (1).
Use the contact only for potential-free normally closed contacts.
External voltage may damage or even destroy the control unit.
Position the push-button in such a way that the operator can see
the door, while he/she is not inside the operating area of the
door.
• Never run the push-button cable along a power cable as this can cause
the control unit to malfunction.
• Install push-button (1) in an appropriate, easily accessible location in
the garage. Minimum height from the floor: 1,6 m
• Install button cable (2) in garage. Connect end of cable to push-but-
ton (1).
Only hold outside edge of control board (1)! Do not touch the
electronic components!
• Undo screw (3) on control unit housing (6), remove light diffuser (4).
Connect the key switches (potential-free NO contact), if any, to
the terminals 5 + 6.
• Lift the control board (1) from the housing (8) and disconnect it from
the terminal bar (2).
• Connect the push-button cable (3) to terminals 5 + 6 of the terminal
bar (2).
• Slot the control board (1) into terminal bar (2) and slide it into the
housing (8).
• Mount the lamp hood (7) and tighten the screw (4).
32
32
7
4
8
3
2
1
2
3
4
5
6
1
2
3
4
5
6
5 6
5
5
7
7
8
8
4
4
6
6
3
3
2
2
1
1
ON
ON
DIP
DIP
2
2
3
3
4
4
5
5
6
6
1
1
1
31
1,6m
2
1
4
3
6
5
C31
1,6m
2
1
A31
`
1
3
A
B
`
½
B31
`
,1
2
6
`
m
°
1,6m
`
,1
2
6
`
m
°
2
`
,1
2
6
`
m
°
1
Seitenansicht 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 34 35

Kommentare zu diesen Handbüchern

Keine Kommentare
  • Excito ViSAGE Locke AdobeAir Jarre Technologies
  • Belkin Flachbildschirmzubehör Sony Fernseher & Monitore Fitbit Personenwaage P3 International Warmwasserbereiter & Kessel Sony Kamerataschen
  • Makita UC3530A Samsung SM-T365 Tii 87 Texet TX-D4450 Canon LV-8320
  • Canon EOS C500 Bedienungsanleitung Hampton Bay 34005 Gebrauchs- und Pflegehandbuch JVC LT-32EM20 Bedienungsanleitung Vega VEGACONNECT 4 Bedienungsanleitung Asus P5KPL-VM Bedienungsanleitung